Aermotor windmills pump water with wind power. Dean Bennett Supply has
served the windmill customer since 1965. Call
800-621-4291 today to get help with your windmill, hand pump, pumping
cylinder and other windmill system accessories. |
|
PUMP |
DEAN BENNETT SUPPLY |
| BAKER ZA HEAVY
DUTY PUMP JACKS BACK BY POPULAR DEMAND for delivery direct from the factory to you. |
|
$ 3015.00 |
#18-ZA BAKER ZA pump jack for use with up to 2 hp electric motor | ||
|
$ 3160.00 |
#20-ZA BAKER ZA pump jack for use with a gasoline engine | ||
|
$ 2425.00 |
#99-ZA BAKER ZA pump jack replacement jack head only | ||
|
$ 199.95 |
#90-ZA Replacement pair of 48" long pumping angles |
| THE BAKER / MONITOR PUMP JACKS are low cost, high quality units used to
reciprocate a pump cylinder. They consist of a helical gear speed reducer driving two
pumping arms ( cranks ) which are connected to the sucker rod by two long pumping angles
and a cross head. These jacks are V-belt driven by either an electric motor or a gasoline
engine mounted directly on the jack. Compared to worm gear pump jacks, Baker's jacks
deliver 50% more power to the sucker rod. All these models are shippable via UPS. THE BAKER ZA pump jack is a heavier duty model designed for deeper wells, heavier loads, and up to 2 hp motor. The pump jack can be mounted on a hand pump or directly on the well pipe itself. A spring-held pump rod pin in the crosshead can be quickly attached or withdrawn. The motor mount is easily adjusted for the base of your electric motor or gas engine and your V-belt length. You can operate the ZA pump jack during a power failure by rotating the jack's pulley with auxiliary power. SPECIFICATIONS: Maximum pump rod load is 1,500 lbs ZA jack is geared 9 to 1 Stroke is 6" Maximum of 42 strokes per minute Weight is 131 lbs |
 |
DEMPSTER WORM GEAR PUMP JACKS Dempster Pump Jack Install Info |
|||
| $ 1285.00 | COMPLETE DEMPSTER PUMP JACK | ||
| $ 1039.00 | DEMPSTER PUMP JACK GEARCASE | ||
| $ 85.00 | PAIR of 48" LONG PITMAN ARMS | ||
COMPLETE JACK: The model BB33-H ( for use with an electric motor ) includes the basic pump jack gearcase, 2 - 48" long pitman arms, crossbar assembly, motor mounting base with motor rails, 8" diameter V-pulley w/ 7/8" bore for jack, 2-1/2" diameter V-pulley w/ 5/8" bore for motor, and 34" long V-belt. Electric Motor IS NOT included in price. Electric motor MUST run counter-clockwise as you face the pulley end of motor. GEAR RATIO & STROKE: Gear ratio is 16 to 1 with a stroke length of 6" recommended maximum is 40 strokes per minute ( 640 RPM shaft speed ) HELICAL MACHINE-CUT GEARS: Precision worms and gears follow a spiral design for a smooth drive. Worms and gears operate right and left, balancing the load and reducing wear, and are pinned to the shaft to maintain proper timing. GEARS RUN IN OIL: Oil seals on all shafts retain lubricant and shut out dirt and moisture from individual gear enclosures on each end. CROSSHEAD COUPLING: Fits 7/16" x 1" flatbar, which must have 12" or more above crosshead for clear operation. Jack gearcase can be attached to slightly larger or smaller barrel by carefully shimming and positioning the U-bolt. LOAD LIMITS: The Dempster Pump Jack should not be used with greater than a 1/2 hp electric motor or a 1-1/2 hp gasoline engine. The speed must not exceed 40 strokes per minute ( 640 RPM shaft speed ) under any circumstances. |
|
|
PUMP JACK CAPACITY TABLE |
DEMPSTER PUMP JACKS |
BAKER PUMP JACKS |
| HEAD IN FEET | CYLINDER | GALLONS | HEAD IN FEET |
| 1/3 hp | 1/2 hp | DIAMETER | PER HOUR | 3/4 hp | 1 hp | 1-1/2 hp | 2 hp |
| 140 | 205 | 1-7/8" | 172 | 154 | 205 | 308 | 410 |
| 125 | 180 | 2" | 195 | 140 | 187 | 281 | 374 |
| 100 | 145 | 2-1/4" | 247 | 117 | 157 | 235 | 313 |
| 75 | 100 | 2-1/2" | 306 | 99 | 133 | 199 | 265 |
| 60 | 90 | 2-3/4" | 370 | 85 | 114 | 170 | 227 |
| 50 | 80 | 3" | 440 | 73 | 98 | 147 | 196 |
FREIGHT IS PREPAID IF ORDER IS OVER $ 1,000.00 |
|
Monitor Baker pump jacks and Dempster pump jacks for gas and electric powered pumping of water wells using a cylinder and sucker rod. With a pump jack you can pump water from a well without needing a windmill or a handpump. Pump jacks are lift pumps that are powered by gas or electricity to stroke sucker rod up and down in a well to operate a cylinder at the bottom.
