HAND PUMPS |
DEAN BENNETT SUPPLY |
| $ 680.00 | #11-HD Hand pump stand with standard open spout | ||
| $ 845.00 | #12-HD Hand pump stand with bibb spout shut off | ||
$ 905.00 |
#12-HDA Hand pump stand with bibb spout, with 2" tapping for tubular well | ||
| $ 1640.00 | #1DFHCS Fountain hand pump stand |
|
|
| $ 415.00 | #100DPS Hand pump shroud conversion kit | ||
| $ 960.00 | #11HDS 11HD Hand Pump with Shroud Conversion Kit Installed | ||
| $ 1145.00 | #12HDS 12HD Hand Pump with Shroud Conversion Kit Installed | ||
| $ 86.50 | #66-MP Sealed pump flange for 6" steel casing | ||
| $ 85.25 | #65-MP Sealed pump flange for 5" steel casing | ||
| $ 82.50 | #64-MP Sealed pump flange for 4" steel casing | ||
| $ 46.00 | #146-HD Allows garden hose connection to spout | ||
| $ 59.00 | #1-HPS Screen Kit for on spout of hand pumps to keep mice out. | ||
|
Baker's force pump stands ( deep well hand pumps ) are for use with windmills, pump jacks, or as a stand alone hand pump. They have a built in surge chamber, an adjustable stroke, and a multi-position cap. The #12-HD is identical to the #11-HD, except that it has a bibb spout in place of the standard open spout. The wheel handle valve in the bibb spout allows you to shut off flow to the spout, which allows water to be diverted thru an outlet plug on the back of the hand pump over to another point ( such as a storage cistern ). |
|||
| Baker's Fountain Pump Stand is available out of the factory on a special order basis, so please allow extra time for delivery. A few strokes of the handle fills a reservoir with water which without further pumping becomes a smooth flowing drinking fountain. Factory installed #100DPS shroud assembly is standard on Fountain Pump Stands. |
|||
| Sealed pump flanges allow your hand pump to be bolted directly onto your steel well casing. |
|||
| Shroud kit replaces the standard pump cap and flat bar to insure added sanitary protection. It is recommended by many state and federal health / sanitary agencies. |
|||
 |
  |
 |
|
|||||||||||||||||||||||||||||||||||||
$ 125.00
#WP2 PLASTIC HAND LIFT PUMP with |
 |
Made of rugged reinforced engineered thermoplastics with stainless steel plunger rod. Will not rust or corrode. Will lift water a maximum of 25 feet. Molded cup will not wear or deteriate. Tapped for 2" pipe, which can be bushed down to smaller pipe. |
|
$ 69.00 #HPP10 15" COUNTER TOP CISTERN PUMP Pictured to the right on bottom |
|
Strictly for shallow well use, as it lifts by suction only. Pumps down to approximately 20'. Tapped for 1-1/4" pipe, has 3" cylinder size cup, and is heavy duty cast iron construction. |
$
680.00 |
#11-HD Hand Pump #66 MP 6" Sealed Flange 84' of 7/16" Galvanized Rod 84' of 1-1/4" Galvanized Pipe 2" All Brass Cylinder 5' of both rod and pipe for inside hand pump base Cylinder Strainer Total Cost of Basic System Possible Add-on's Pipe holder secures drop pipe while lowering or pulling galvanized pipe Pipe Dog - Economical pipe lifting and setting tool Each additional 21' of pipe and rod if your well is deeper #12-HD with bibb spout in place of #11-HD |
 |
Hand Pump Helpful Hints: click here for common questions about using a hand pump as a back-up water source. |
HOME Y2K Hand Pump Simple Hand Pump Pump Jacks Cylinders Prices effective 1/5/2008 |
