Aermotor windmills pump water with wind power. Dean Bennett Supply has served the windmill customer since 1965.

Aermotor windmills pump water with wind power. Dean Bennett Supply has served the windmill customer since 1965. Call 800-621-4291 today to get help with your windmill, hand pump, pumping cylinder and other windmill system accessories.
 

SUBMERSIBLE PUMP
FOR BELOW A WINDMILL CYLINDER

DEAN BENNETT SUPPLY
PH 1-800-621-4291
Smart Phone Dialable

What to do when the wind doesn't blow
Pump under Windmill Cylinder Catalog Page 54a

Putting a submersible pump below a windmill cylinder for when the wind doesn't blow. Pictured to the left is our cylinder with submersible pump assembly for installation under a windmill. This assembly will allow your windmill to pump water with wind power when there is enough wind available. When the wind is not sufficient to pump water with the windmill, you can switch the electric powered submersible pump on to supply the water. You can either use a gas powered generator or standard electric power to run the submersible pump during low wind conditions.

Only the highest quality components are used in this assembly. All piping and fittings shown are brass. The cylinder is an all brass construction with a brass ball valve and a brass ball check. We have found that ball valves react better than poppet valves when pumping water through the cylinder with a submersible pump. The submersible pump used in this system is our deluxe stainless steel Flint & Walling S-model pump with Franklin Electric's stainless steel submersible motor. The assembly prices shown below include everything pictured to the left.


1/2 hp     10 gallon per minute submersible assembly    
$ 941.00

0 psi discharge 40' = 15.6
gpm
60' = 14.7
gpm
80' = 14.2
gpm
100' = 13.4
gpm
120' = 12.6
gpm
140' = 11.7
gpm
160' = 10.8
gpm
180' = 9.7
gpm
200' = 8.3
gpm
225' = 6.3
gpm

The above capacities are shown at open discharge as your normal usage will be filling a stock tank or an open storage tank. This model is available in either 115 volt or 230 volt power.


1/2 hp     5 gallon per minute deep set submersible assembly     $ 1119.00
0 psi discharge 40' = 9.9
gpm
60' = 9.6
gpm
80' = 9.2
gpm
100' = 8.9
gpm
120' = 8.5
gpm
140' = 8.2
gpm
160' = 7.8
gpm
180' = 7.4
gpm
200' = 7.0
gpm
225' = 6.5
gpm
250' = 5.9
gpm
275' = 5.3
gpm
300' = 4.7
gpm
325' = 4.0
gpm
350' = 3.2
gpm
The above capacities are shown at open discharge. This model is available in either 115 volt or 230 volt power.

3/4 hp     10 gallon per minute submersible assembly    
$ 1019.00
0 psi discharge 60' = 15.5
gpm
80' = 15.0
gpm
100' = 14.6
gpm
120' = 14.1
gpm
140' = 13.6
gpm
160' = 13.1
gpm
180' = 12.5
gpm
200' = 12.0
gpm
225' = 11.3
gpm
250' = 10.4
gpm
275' = 9.7
gpm
300' = 8.5
gpm
325' = 7.4
gpm
350' = 5.7
gpm
The above capacities are at open discharge, and this model is only available in 230 volt power.


1 hp     10 gallon per minute submersible assembly     $ 1076.00

0 psi discharge 80' = 15.4
gpm
100' = 15.1
gpm
120' = 14.7
gpm
140' = 14.3
gpm
160' = 13.9
gpm
180' = 13.6
gpm
200' = 13.1
gpm
225' = 12.6
gpm
250' = 12.0
gpm
275' = 11.4
gpm
300' = 10.8
gpm
325' = 10.2
gpm
350' = 9.3
gpm
400' = 7.4
gpm
450' = 3.8
gpm
The above capacities are at open discharge, and this model is only available in 230 volt power.

HOME

Download our catalog in pdf format

Prices effective July 15, 2013