PITLESS WELL CAPS
AND WELL SEALS
ALUMINUM PITLESS WELL CAPS
|
PITLESS WELL CAPS |
|
|
|
| Pitless well caps fit over the top of your well casing. Be sure you measure across the top of the casing to determine the proper size well cap. These pitless well caps are low profile aluminum well caps, designed to go over the top of a well casing where a pitless adapter is installed in the pipe for underground discharge of the water from the pump to the house. The bottom half of this two piece cap slides down over the well casing, sealing on the top of the pipe, and secured with allen head screws. An O-ring goes on top of the lower half, and the top half bolts down to the lower half. There is a screen built into the bottom half, for well venting, and a 1" conduit tap for routing the pump wire out of the well. When the top half of the pitless well cap is removed, clear access to the well is provided, while allowing you to keep all your wiring attached. | |||
| LX4-1 |
|
LX41 | $ 41.95 |
| 45WE1 |
|
45WE1 | $ 60.50 |
| LX5-1 |
|
LX51 | $ 41.00 |
| LX6-1 |
|
LX61 | $ 43.75 |
| 658LKWT |
|
658LKWT | $ 95.00 |
| WTCC6.6 |
|
WTCC66 | $ 76.50 |
| AWTC8 |
|
AWTC8 | $ 80.75 |
|
CAST IRON WELL SEALS |
| Water
well pumps that discharge through the top of the well, use a cast iron well seal
that compresses a rubber seal inside the well casing, and around the outside of
the pump discharge pipe. When ordering a well seal, remember that it fits inside
the well casing, so your measurement should be the ID of the casing. The pipe
size used from the pump up out of the well, is the size to order for the center
hole. The well seal is placed into the top of the casing, with the pump discharge pipe through the center. The bolts that secure the two cast iron halves together are tightened to expand the rubber seal out against the well casing inside, and against the outside of the discharge pipe. There is a opening for a 1/2" vent, and an opening for your pump wire to be routed through. |
 |
|
SINGLE HOLE WELL SEALS FOR
SUBMERSIBLE PUMPS |
| 20CIA |
|
2" Cast Iron Well Seal |
$ 39.00 |
40CIA 40CIB 40CID |
4" cast iron well seal for inside 4" ID well casing, stocked for 1", 1-1/4", and 2" drop pipe with a 3/4" female threaded conduit opening. Split seal. |
4" Cast
Iron Well Seal |
$ 20.25 |
40ABSA 40ABSB |
|
4" ABS Well Seal |
$ 20.25 |
42CIA 42CIB |
|
4-1/4" Cast Iron Well Seal |
$ 20.25 |
45CIA 45CIB |
|
4-1/2" Cast Iron Well Seal |
$ 28.95 |
50CIA 50CIB 50CIC 50CID |
|
5" Cast Iron Well Seal |
$ 30.50 |
56CIA 56CIB |
|
5-5/8" Cast Iron Well Seal |
$ 33.75 |
60CIA 60CIB 60CIC 60CID |
|
6" Cast Iron Well Seal |
$ 33.90 |
62CIA 62CIB 62CIC 62CID |
|
6-1/4" Cast Iron Well Seal |
$ 33.90 |
65CIA |
|
6-1/2" Cast Iron Well Seal |
$ 74.50 |
80CIA 80CIB 80CID |
8" cast iron well seal for inside 8" ID well casing, stocked for 1", 1-1/4", and 2" drop pipe, with a 1" female threaded conduit connection. Split seal. |
8" Cast Iron Well Seal |
$ 101.00 |
| 10CID |
10" cast iron well seal for inside 10" ID well casing. Stocked for 2" drop pipe, with 1" female threaded conduit connection.1 piece solid seal. |
10" Cast Iron Well Seal |
$ 115.00 |
|
JET PUMP - DOUBLE HOLE WELL
SEALS |
 |
|
Double hole cast iron well seals
are used with jet pumps to provide access for two pipes going down to a jet pump
deep well ejector package. Normal configuration is to have a 1" pipe size
and a 1-1/4" pipe size hole for the pipe. We stock some sizes in 1"
for both holes. |
40CIDHA 40CIDHB |
|
4" Cast Iron Double Hole Well Seal |
$ 19.50 |
45CIDHA |
|
4-1/2" Cast Iron Double Hole Well Seal |
$ 52.25 |
50CIDHA 50CIDHB |
|
5" Cast Iron Double Hole Well Seal |
$ 30.25 |
56CIDHA |
|
5-5/8" Cast Iron Double Hole Well Seal |
$ 31.75 |
60CIDHA 60CIDHB |
|
6" Cast Iron Double Hole Well Seal |
$ 32.50 |
62CIDHA |
|
6-1/4" Cast Iron Double Hole Well Seal |
$ 32.50 |
|
DEAN BENNETT SUPPLY COMPANY |
|
Prices effective November 25, 2009 |